- Home
- ยป
- Our Products
- »
- Industrial Fasteners & Clamps
Industrial Fasteners & Clamps
A fastener or fastening is a hardware device that mechanically joins or affixes two or more objects together. In general, fasteners are used to create non-permanent joint that is, joints that can be removed or dismantled without damaging the joining components. Welding is an example of creating permanent joints.
MS Anchor Fasteners
Minimum Order Quantity: 100 Piece
Size | 10000mm |
Brand | PEC |
Material | Mild Steel |
Type Of Bolts | Pin/ Bolt |
Color | Chrome |
Surface Treatment | Polished |
J & L Bolts | 7" |
Taper Washers | 24 mm |
Connector | M16 |
Mild steel fasteners are widely used for all general purposes where high strength and corrosion resistance is not required. Their low cost makes them ideal for everyday use. Mild steel Bolts and Screws conform to grades 4.6 and 4.8 and Nuts to grade 4. Higher grades of 5.6 and 5 are also arranged against order.
Finishes:
- Self colour, Zinc plated (with White/Blue/Yellow passivation), Hot Dip galvanised, Cadmium Plated, Blackened, Nickle plated and Chromium Plated.
Hexagonal Head Bolts and Screws:
- M3 X 6MM to M48 X 300 generally conforming to IS 1363(Part 1 & 2) 2002
- 3/16” X 1/2” to 2” X 12” in BSW threads generally conforming to BS 916
Hexagonal Full and Lock (Thin) Nuts:
- M2 to M60 generally conforming to IS 1363(Part 3)2002 (Hex Nut) and to IS 1364(Part 4)2003 (Lock (Thin) Nut)
- 1/8” to 2” in BSW threadsgenerally conforming to BS 916
- 1/2” to 3” in BSP threadsgenerally conforming to IS 3468-1991
Left hand thread nuts:
- 1/4" to 1" in BSW threads
- M6 to M24 in MM threads
Square Head Bolts & Nuts:
- M5 to M12generally conforming to IS 2585-2006
- 1/8” to 1/2” in BSW threads
Dom Nuts:
- M6 to M24
Flange (Collar) Bolts and nuts:
- M6 x 12 to M10 x 25mm
Eye Bolts and Eye nuts:
- Lifting Hooks M8 to M48
- Eye Bolt (Small Eye) M8 x 40 to M24 x 200
- Eye Nuts M12 to M 20
Slotted and Castle Nuts:
- M10 to M48 generally conforming to IS 2232-1967
- 3/8" to 2" in BSW threads
Nyloc Nuts:
- M3 to M48 generally conforming to IS7002-2005
- 1/4" to 1" in BSW, UNC, UNF and BSF threads.
Wing Nuts (Cast Iron):
- M6 to M16
- 1/4" to 5/8" in BSW threads
Studs:
- M6 x 25mm to M20 x 100mm
- 1/4" x 1" to 3/4" x 4"
Snap Head Rivets:
- 6 x 12mm to 24 x 100mm generally conforming to IS 1929/1982 and IS 2155/1982
- 1/4" x 1/2" to 1" x 4"
Carriage Bolts:
- 1/4" x 1 1/2" to 1/2" to 12"
- Special C.P. Carriage bolts with Nut and Washers 1/4" x 1 1/2" to 3" (for C.P.Aldrops)
Plain Washers:
- 3mm to 64mm generally conforming to IS 2016/67
- 1/8" to 2"
Taper Washers:
- 12mm to 24mm
U Bolts:
- Suitable for pipe sizes of 3/4" to 12" with bolt dia of 8mm to 12mm
Pipe Bolts:
- 5/16" x 3" to 7" suitable for pipes of 1" to 2"
J & L Bolts:
- 5/16" x 3" to 7"
GI Threaded Rods:
- M6 to M20 in 1Mtr & 2Mtr length
Connecter (Long) Nut:
- M6 to M16
GI U Clamp
Size | 1/2" |
Material | Galvanized Iron |
Shape | U |
Brand | PEC |
Usage/Application | Industrial |
Working Temperature | 200 Degree C |
Clamp Type | Fixed Wall |
The distinction between a bolt and a screw is commonly misunderstood. There are several practical differences, but most have some degree of overlap between bolts and screws.
The defining distinction, per Machinery's Handbook, is in their intended purpose: Bolts are for the assembly of two unthreaded components, with the aid of a nut. Screws in contrast are used in components which contain their own thread, and the screw may even cut its own internal thread into them. Many threaded fasteners can be described as either screws or bolts, depending on how they are used.
Bolts are often used to make a bolted joint. This is a combination of the nut applying an axial clamping force and also the shank of the bolt acting as a dowel, pinning the joint against sideways shear forces. For this reason, many bolts have a plain unthreaded shank (called the grip length) as this makes for a better, stronger dowel. The presence of the unthreaded shank has often been given as characteristic of bolts vs. screws, but this is incidental to its use, rather than defining. The grip length should be chosen carefully, to be around the same length as the thickness of the materials, and any washers, bolted together. Too short places the dowel shear load onto the threads, which may cause fretting wear on the hole. Too long prevents the nut from being tightened down correctly. No more than two turns of the thread should be within the hole.
Where a fastener forms its own thread in the component being fastened, it is called a screw. This is most obviously so when the thread is tapered (i.e. traditional wood screws), precluding the use of a nut, or when a sheet metal screw or other thread-forming screw is used.
A screw must always be turned to assemble the joint. Many bolts are held fixed in place during assembly, either by a tool or by a design of non-rotating bolt, such as a carriage bolt, and only the corresponding nut is turned.
Jubilee Hose Clamp
Minimum Order Quantity: 100 Piece
Size | 1 mm - 5 mm |
Material | Stainless Steel |
Surface Treatment | Polished |
Usage/Application | Industrial |
Product Type | Hose Clamp |
Country of Origin | Made in India |
We have in store a wide array of Stainless Steel Worm Drive Hose Clamp, which is made keeping in mind the requirements of chemical, food and marine industry at our vendors' end. Our vendors design the offered hose clamp as using advanced tool to ensure their accurate design. Moreover, they manufacture these hose clamps by making use of high grade raw material to provide non throbbing surfaces on the clamp which protect the hose from damages. Apart from this, a a recommended clip can be used for smaller diameters in case of emergency requirements since the perforations on the clamps are done at extended lengths.
Features:
- Seal the hose onto a fixed fitting
- Protects the hose
- Longer service life
Klipco Hose Clamp
Minimum Order Quantity: 100 Piece
Color | White |
Material | Mild Steel |
Size | 3" |
Material Grade | IS:1239 |
Usage/Application | Industrial |
Shape | Round |
Product Type | Hose Clamp |
Brand | Klipco |
Country of Origin | Made in India |
We have in store a wide array of Stainless Steel Worm Drive Hose Clamp, which is made keeping in mind the requirements of chemical, food and marine industry at our vendors' end. Our vendors design the offered hose clamp as using advanced tool to ensure their accurate design. Moreover, they manufacture these hose clamps by making use of high grade raw material to provide non throbbing surfaces on the clamp which protect the hose from damages. Apart from this, a a recommended clip can be used for smaller diameters in case of emergency requirements since the perforations on the clamps are done at extended lengths.
Features:
- Seal the hose onto a fixed fitting
- Protects the hose
- Longer service life
GI Pipe Hook
Minimum Order Quantity: 100 Kg
Installation Type | Hanging Type |
Hook Type | J |
Material | Galvanized Iron |
Brand | PEC |
Usage/Application | Industrial |
Load Capacity | 50 Kg |
Surface Finishing | Polished |
Country of Origin | Made in India |
Available Hook Type:
- J, L, and V
Ms J Hook
Minimum Order Quantity: 100 Kg
Material | Iron |
Brand | PEC |
Usage/Application | Industrial |
Hook Type | Various |
Installation Type | Screw in |
Country of Origin | Made in India |
High Tensile Bolt Nut
Minimum Order Quantity: 100 Kg
Usage/Application | Industrial |
Size | 75 mm |
Thread Type | BSPT |
Grade | A105 |
Standard | ASTM |
Head Shape | Hexagonal |
Technique | Hot Rolled |
Material | Carbon Steel |
Country of Origin | Made in India |
We are successfully meeting the varied needs of our patrons by offering a wide gamut of High Tension Nut Boltas per their precise needs.
The distinction between a bolt and a screw is commonly misunderstood. There are several practical differences, but most have some degree of overlap between bolts and screws.
The defining distinction, per Machinery's Handbook, is in their intended purpose: Bolts are for the assembly of two unthreaded components, with the aid of a nut. Screws in contrast are used in components which contain their own thread, and the screw may even cut its own internal thread into them. Many threaded fasteners can be described as either screws or bolts, depending on how they are used.
Bolts are often used to make a bolted joint. This is a combination of the nut applying an axial clamping force and also the shank of the bolt acting as a dowel, pinning the joint against sideways shear forces. For this reason, many bolts have a plain unthreaded shank (called the grip length) as this makes for a better, stronger dowel. The presence of the unthreaded shank has often been given as characteristic of bolts vs. screws, but this is incidental to its use, rather than defining. The grip length should be chosen carefully, to be around the same length as the thickness of the materials, and any washers, bolted together. Too short places the dowel shear load onto the threads, which may cause fretting wear on the hole. Too long prevents the nut from being tightened down correctly. No more than two turns of the thread should be within the hole.
Where a fastener forms its own thread in the component being fastened, it is called a screw. This is most obviously so when the thread is tapered (i.e. traditional wood screws), precluding the use of a nut, or when a sheet metal screw or other thread-forming screw is used.
A screw must always be turned to assemble the joint. Many bolts are held fixed in place during assembly, either by a tool or by a design of non-rotating bolt, such as a carriage bolt, and only the corresponding nut is turned.
SS Stud Bolt
Minimum Order Quantity: 100 Piece
Material | Stainless Steel |
Usage/Application | Industrial |
Product Type | Bolt |
Size | 1/2" |
Grade | CF8M |
Head Shape | Round |
Surface Treatment | Chrome |
Material Grade | SS304 |
Country of Origin | Made in India |
We are successfully meeting the varied needs of our patrons by offering a wide gamut of Stud Bolt.
The distinction between a bolt and a screw is commonly misunderstood. There are several practical differences, but most have some degree of overlap between bolts and screws.
The defining distinction, per Machinery's Handbook, is in their intended purpose: Bolts are for the assembly of two unthreaded components, with the aid of a nut. Screws in contrast are used in components which contain their own thread, and the screw may even cut its own internal thread into them. Many threaded fasteners can be described as either screws or bolts, depending on how they are used.
Bolts are often used to make a bolted joint. This is a combination of the nut applying an axial clamping force and also the shank of the bolt acting as a dowel, pinning the joint against sideways shear forces. For this reason, many bolts have a plain unthreaded shank (called the grip length) as this makes for a better, stronger dowel. The presence of the unthreaded shank has often been given as characteristic of bolts vs. screws,[3] but this is incidental to its use, rather than defining. The grip length should be chosen carefully, to be around the same length as the thickness of the materials, and any washers, bolted together. Too short places the dowel shear load onto the threads, which may cause fretting wear on the hole. Too long prevents the nut from being tightened down correctly. No more than two turns of the thread should be within the hole.
Where a fastener forms its own thread in the component being fastened, it is called a screw. This is most obviously so when the thread is tapered (i.e. traditional wood screws), precluding the use of a nut, or when a sheet metal screw or other thread-forming screw is used.
A screw must always be turned to assemble the joint. Many bolts are held fixed in place during assembly, either by a tool or by a design of non-rotating bolt, such as a carriage bolt, and only the corresponding nut is turned.
Gi U Bolt
Minimum Order Quantity: 100 Piece
Material | Stainless Steel |
Bolt Shape | U |
Usage/Application | Pipe Fittings |
Size | 1/2" |
Type Of Bolts | Screwed |
Head Type | Round |
Finishing Type | Polished |
Country of Origin | Made in India |
The distinction between a bolt and a screw is commonly misunderstood. There are several practical differences, but most have some degree of overlap between bolts and screws.
The defining distinction, per Machinery's Handbook, is in their intended purpose: Bolts are for the assembly of two unthreaded components, with the aid of a nut. Screws in contrast are used in components which contain their own thread, and the screw may even cut its own internal thread into them. Many threaded fasteners can be described as either screws or bolts, depending on how they are used.
Bolts are often used to make a bolted joint. This is a combination of the nut applying an axial clamping force and also the shank of the bolt acting as a dowel, pinning the joint against sideways shear forces. For this reason, many bolts have a plain unthreaded shank (called the grip length) as this makes for a better, stronger dowel. The presence of the unthreaded shank has often been given as characteristic of bolts vs. screws, but this is incidental to its use, rather than defining. The grip length should be chosen carefully, to be around the same length as the thickness of the materials, and any washers, bolted together. Too short places the dowel shear load onto the threads, which may cause fretting wear on the hole. Too long prevents the nut from being tightened down correctly. No more than two turns of the thread should be within the hole.
Where a fastener forms its own thread in the component being fastened, it is called a screw. This is most obviously so when the thread is tapered (i.e. traditional wood screws), precluding the use of a nut, or when a sheet metal screw or other thread-forming screw is used.
A screw must always be turned to assemble the joint. Many bolts are held fixed in place during assembly, either by a tool or by a design of non-rotating bolt, such as a carriage bolt, and only the corresponding nut is turned.
Ms Stud Bolt
Minimum Order Quantity: 100 Piece
Size | 1000 mm |
Standard | ASTM |
Material | Mild Steel |
Usage/Application | Industrial |
Head Shape | Round |
Thread Type | BSPT |
Diameter | 15 mm |
Threads | 40 mm |
Country of Origin | Made in India |
Mild steel fasteners are widely used for all general purposes where high strength and corrosion resistance is not required. Their low cost makes them ideal for everyday use. Mild steel Bolts and Screws conform to grades 4.6 and 4.8 and Nuts to grade 4. Higher grades of 5.6 and 5 are also arranged against order.
Finishes: Self colour, Zinc plated (with White/Blue/Yellow passivation), Hot Dip galvanised, Cadmium Plated, Blackened, Nickle plated and Chromium Plated.
Hexagonal Head Bolts and Screws:
- M3 X 6MM to M48 X 300 generally conforming to IS 1363(Part 1 & 2) 2002
- 3/16” X 1/2” to 2” X 12” in BSW threads generally conforming to BS 916
Hexagonal Full and Lock (Thin) Nuts:
- M2 to M60 generally conforming to IS 1363(Part 3)2002 (Hex Nut) and to IS 1364(Part 4)2003 (Lock (Thin) Nut)
- 1/8” to 2” in BSW threadsgenerally conforming to BS 916
- 1/2” to 3” in BSP threadsgenerally conforming to IS 3468-1991
Left hand thread nuts:
- 1/4" to 1" in BSW threads
- M6 to M24 in MM threads
Square Head Bolts & Nuts:
- M5 to M12generally conforming to IS 2585-2006
- 1/8” to 1/2” in BSW threads
Dom Nuts:
- M6 to M24
Flange (Collar) Bolts and nuts:
- M6 x 12 to M10 x 25mm
Eye Bolts and Eye nuts:
- Lifting Hooks M8 to M48
- Eye Bolt (Small Eye) M8 x 40 to M24 x 200
- Eye Nuts M12 to M 20
Slotted and Castle Nuts:
- M10 to M48 generally conforming to IS 2232-1967
- 3/8" to 2" in BSW threads
Nyloc Nuts:
- M3 to M48 generally conforming to IS7002-2005
- 1/4" to 1" in BSW, UNC, UNF and BSF threads.
Wing Nuts (Cast Iron):
- M6 to M16
- 1/4" to 5/8" in BSW threads
Studs:
- M6 x 25mm to M20 x 100mm
- 1/4" x 1" to 3/4" x 4"
Snap Head Rivets:
- 6 x 12mm to 24 x 100mm generally conforming to IS 1929/1982 and IS 2155/1982
- 1/4" x 1/2" to 1" x 4"
Carriage Bolts:
- 1/4" x 1 1/2" to 1/2" to 12"
- Special C.P. Carriage bolts with Nut and Washers 1/4" x 1 1/2" to 3" (for C.P.Aldrops)
Plain Washers:
- 3mm to 64mm generally conforming to IS 2016/67
- 1/8" to 2"
Taper Washers:
- 12mm to 24mm
U Bolts:
- Suitable for pipe sizes of 3/4" to 12" with bolt dia of 8mm to 12mm
Pipe Bolts:
- 5/16" x 3" to 7" suitable for pipes of 1" to 2"
J & L Bolts:
- 5/16" x 3" to 7"
GI Threaded Rods:
- M6 to M20 in 1Mtr & 2Mtr length
Connecter (Long) Nut:
- M6 to M16
Stainless Steel 304 Fasteners
Minimum Order Quantity: 100 Piece
Material Grade | SS304 |
Material | Stainless Steel |
Size | 100 mm |
Head Style | Round Head |
Surface Treatment | Polished |
Packaging Type | Plastic Packet |
Technique | Hot Rolled |
Product Code | CF8M |
Country of Origin | Made in India |
Mild steel fasteners are widely used for all general purposes where high strength and corrosion resistance is not required. Their low cost makes them ideal for everyday use. Mild steel Bolts and Screws conform to grades 4.6 and 4.8 and Nuts to grade 4. Higher grades of 5.6 and 5 are also arranged against order.
Finishes: Self colour, Zinc plated (with White/Blue/Yellow passivation), Hot Dip galvanised, Cadmium Plated, Blackened, Nickle plated and Chromium Plated.
Hexagonal Head Bolts and Screws:
- M3 X 6MM to M48 X 300 generally conforming to IS 1363(Part 1 & 2) 2002
- 3/16” X 1/2” to 2” X 12” in BSW threads generally conforming to BS 916
Hexagonal Full and Lock (Thin) Nuts:
- M2 to M60 generally conforming to IS 1363(Part 3)2002 (Hex Nut) and to IS 1364(Part 4)2003 (Lock (Thin) Nut)
- 1/8” to 2” in BSW threadsgenerally conforming to BS 916
- 1/2” to 3” in BSP threadsgenerally conforming to IS 3468-1991
Left hand thread nuts:
- 1/4" to 1" in BSW threads
- M6 to M24 in MM threads
Square Head Bolts & Nuts:
- M5 to M12generally conforming to IS 2585-2006
- 1/8” to 1/2” in BSW threads
Dom Nuts:
- M6 to M24
Flange (Collar) Bolts and nuts:
- M6 x 12 to M10 x 25mm
Eye Bolts and Eye nuts:
- Lifting Hooks M8 to M48
- Eye Bolt (Small Eye) M8 x 40 to M24 x 200
- Eye Nuts M12 to M 20
Slotted and Castle Nuts:
- M10 to M48 generally conforming to IS 2232-1967
- 3/8" to 2" in BSW threads
Nyloc Nuts:
- M3 to M48 generally conforming to IS7002-2005
- 1/4" to 1" in BSW, UNC, UNF and BSF threads.
Wing Nuts (Cast Iron):
- M6 to M16
- 1/4" to 5/8" in BSW threads
Studs:
- M6 x 25mm to M20 x 100mm
- 1/4" x 1" to 3/4" x 4"
Snap Head Rivets:
- 6 x 12mm to 24 x 100mm generally conforming to IS 1929/1982 and IS 2155/1982
- 1/4" x 1/2" to 1" x 4"
Carriage Bolts:
- 1/4" x 1 1/2" to 1/2" to 12"
- Special C.P. Carriage bolts with Nut and Washers 1/4" x 1 1/2" to 3" (for C.P.Aldrops)
Plain Washers:
- 3mm to 64mm generally conforming to IS 2016/67
- 1/8" to 2"
Taper Washers:
- 12mm to 24mm
U Bolts:
- Suitable for pipe sizes of 3/4" to 12" with bolt dia of 8mm to 12mm
Pipe Bolts:
- 5/16" x 3" to 7" suitable for pipes of 1" to 2"
J & L Bolts:
- 5/16" x 3" to 7"
GI Threaded Rods:
- M6 to M20 in 1Mtr & 2Mtr length
Connecter (Long) Nut:
- M6 to M16
GI Fastener .
Minimum Order Quantity: 100 Piece
Size | 1 inch |
Material | Galvanized Iron |
Brand | PEC |
Grade | IS:1239 |
Head Shape | Round |
Packaging Type | Cartoon Box |
Technique | Hot Rolled |
Country of Origin | Made in India |
Mild steel fasteners are widely used for all general purposes where high strength and corrosion resistance is not required. Their low cost makes them ideal for everyday use. Mild steel Bolts and Screws conform to grades 4.6 and 4.8 and Nuts to grade 4. Higher grades of 5.6 and 5 are also arranged against order.
Finishes:
- Self colour, Zinc plated (with White/Blue/Yellow passivation), Hot Dip galvanised, Cadmium Plated, Blackened, Nickle plated and Chromium Plated.
Specifications:
- Hexagonal Head Bolts and Screws: M3 X 6MM to M48 X 300 generally conforming to IS 1363(Part 1 & 2) 2002, 3/16” X 1/2” to 2” X 12” in BSW threads generally conforming to BS 916. Hexagonal Full and Lock (Thin) Nuts: M2 to M60 generally conforming to IS 1363(Part 3)2002 (Hex Nut) and to IS 1364(Part 4)2003 (Lock (Thin) Nut), 1/8” to 2” in BSW threadsgenerally conforming to BS 916, 1/2” to 3” in BSP threadsgenerally conforming to IS 3468-1991
- Left hand thread nuts: 1/4" to 1" in BSW threads, M6 to M24 in MM threads
- Square Head Bolts & Nuts: M5 to M12generally conforming to IS 2585-2006, 1/8” to 1/2” in BSW threads
- Dom Nuts: M6 to M24
- Flange (Collar) Bolts and nuts: M6 x 12 to M10 x 25mm
- Eye Bolts and Eye nuts: Lifting Hooks M8 to M48, Eye Bolt (Small Eye) M8 x 40 to M24 x 200, Eye Nuts M12 to M 20
- Slotted and Castle Nuts: M10 to M48 generally conforming to IS 2232-1967. 3/8" to 2" in BSW threads
- Nyloc Nuts: M3 to M48 generally conforming to IS7002-2005, 1/4" to 1" in BSW, UNC, UNF and BSF threads.
- Wing Nuts (Cast Iron): M6 to M16, 1/4" to 5/8" in BSW threads
- Studs: M6 x 25mm to M20 x 100mm, 1/4" x 1" to 3/4" x 4"
- Snap Head Rivets: 6 x 12mm to 24 x 100mm generally conforming to IS 1929/1982 and IS 2155/1982, 1/4" x 1/2" to 1" x 4"
- Carriage Bolts: 1/4" x 1 1/2" to 1/2" to 12", Special C.P. Carriage bolts with Nut and Washers 1/4" x 1 1/2" to 3" (for C.P.Aldrops)
- Plain Washers: 3mm to 64mm generally conforming to IS 2016/67, 1/8" to 2"
- Taper Washers: 12mm to 24mm
- U Bolts: Suitable for pipe sizes of 3/4" to 12" with bolt dia of 8mm to 12mm
- Pipe Bolts: 5/16" x 3" to 7" suitable for pipes of 1" to 2"
- J & L Bolts: 5/16" x 3" to 7"
- GI Threaded Rods: M6 to M20 in 1Mtr & 2Mtr length
- Connecter (Long) Nut: M6 to M16
SS Nut Bolt
Minimum Order Quantity: 100 Piece
Size | 100 mm |
Nut Type | Broaching |
Usage/Application | Industrial |
Shape | Round |
Brand | PEC |
Thread Type | 20 mm |
Packaging Type | Jute Bag |
The distinction between a bolt and a screw is commonly misunderstood. There are several practical differences, but most have some degree of overlap between bolts and screws.
The defining distinction, per Machinery's Handbook, is in their intended purpose: Bolts are for the assembly of two unthreaded components, with the aid of a nut. Screws in contrast are used in components which contain their own thread, and the screw may even cut its own internal thread into them. Many threaded fasteners can be described as either screws or bolts, depending on how they are used.
Bolts are often used to make a bolted joint. This is a combination of the nut applying an axial clamping force and also the shank of the bolt acting as a dowel, pinning the joint against sideways shear forces. For this reason, many bolts have a plain unthreaded shank (called the grip length) as this makes for a better, stronger dowel. The presence of the unthreaded shank has often been given as characteristic of bolts vs. screws,[3] but this is incidental to its use, rather than defining. The grip length should be chosen carefully, to be around the same length as the thickness of the materials, and any washers, bolted together. Too short places the dowel shear load onto the threads, which may cause fretting wear on the hole. Too long prevents the nut from being tightened down correctly. No more than two turns of the thread should be within the hole.
Where a fastener forms its own thread in the component being fastened, it is called a screw. This is most obviously so when the thread is tapered (i.e. traditional wood screws), precluding the use of a nut, or when a sheet metal screw or other thread-forming screw is used.
A screw must always be turned to assemble the joint. Many bolts are held fixed in place during assembly, either by a tool or by a design of non-rotating bolt, such as a carriage bolt, and only the corresponding nut is turned.
MS Nut Bolt
Minimum Order Quantity: 100 Piece
Diameter | 10 mm |
Usage/Application | Industrial |
Bolt Type | Screwed |
Surface Finishing | Polished |
Size | 100 mm |
Threaded | Full Threaded |
Material | Mild Steel |
Head Shape | Hexagonal |
Country of Origin | Made in India |
The distinction between a bolt and a screw is commonly misunderstood. There are several practical differences, but most have some degree of overlap between bolts and screws.
The defining distinction, per Machinery's Handbook, is in their intended purpose: Bolts are for the assembly of two unthreaded components, with the aid of a nut. Screws in contrast are used in components which contain their own thread, and the screw may even cut its own internal thread into them. Many threaded fasteners can be described as either screws or bolts, depending on how they are used.
Bolts are often used to make a bolted joint. This is a combination of the nut applying an axial clamping force and also the shank of the bolt acting as a dowel, pinning the joint against sideways shear forces. For this reason, many bolts have a plain unthreaded shank (called the grip length) as this makes for a better, stronger dowel. The presence of the unthreaded shank has often been given as characteristic of bolts vs. screws, but this is incidental to its use, rather than defining. The grip length should be chosen carefully, to be around the same length as the thickness of the materials, and any washers, bolted together. Too short places the dowel shear load onto the threads, which may cause fretting wear on the hole. Too long prevents the nut from being tightened down correctly. No more than two turns of the thread should be within the hole.
Where a fastener forms its own thread in the component being fastened, it is called a screw. This is most obviously so when the thread is tapered (i.e. traditional wood screws), precluding the use of a nut, or when a sheet metal screw or other thread-forming screw is used.
A screw must always be turned to assemble the joint. Many bolts are held fixed in place during assembly, either by a tool or by a design of non-rotating bolt, such as a carriage bolt, and only the corresponding nut is turned.
GI Nut Bolt
Minimum Order Quantity: 100 Kg
Size | 75 mm |
Nut Type | Drilling |
Material | Galvanized Iron |
Part Number | IS:1239 |
Color | Chrome |
Usage/Application | Industrial |
Head Shape | Hexagonal |
Country of Origin | Made in India |
The distinction between a bolt and a screw is commonly misunderstood. There are several practical differences, but most have some degree of overlap between bolts and screws.
The defining distinction, per Machinery's Handbook, is in their intended purpose: Bolts are for the assembly of two unthreaded components, with the aid of a nut. Screws in contrast are used in components which contain their own thread, and the screw may even cut its own internal thread into them. Many threaded fasteners can be described as either screws or bolts, depending on how they are used.
Bolts are often used to make a bolted joint. This is a combination of the nut applying an axial clamping force and also the shank of the bolt acting as a dowel, pinning the joint against sideways shear forces. For this reason, many bolts have a plain unthreaded shank (called the grip length) as this makes for a better, stronger dowel. The presence of the unthreaded shank has often been given as characteristic of bolts vs. screws, but this is incidental to its use, rather than defining. The grip length should be chosen carefully, to be around the same length as the thickness of the materials, and any washers, bolted together. Too short places the dowel shear load onto the threads, which may cause fretting wear on the hole. Too long prevents the nut from being tightened down correctly. No more than two turns of the thread should be within the hole.
Where a fastener forms its own thread in the component being fastened, it is called a screw. This is most obviously so when the thread is tapered (i.e. traditional wood screws), precluding the use of a nut, or when a sheet metal screw or other thread-forming screw is used.
A screw must always be turned to assemble the joint. Many bolts are held fixed in place during assembly, either by a tool or by a design of non-rotating bolt, such as a carriage bolt, and only the corresponding nut is turned.
Ht Nut Bolt
Minimum Order Quantity: 100 Piece
Usage/Application | Industrial |
Size | 25 mm |
Thread Type | BSPT |
Grade | A105 |
Standard | ASTM |
Material | Carbon Steel |
Country of Origin | Made in India |
The distinction between a bolt and a screw is commonly misunderstood. There are several practical differences, but most have some degree of overlap between bolts and screws.
The defining distinction, per Machinery's Handbook, is in their intended purpose: Bolts are for the assembly of two unthreaded components, with the aid of a nut. Screws in contrast are used in components which contain their own thread, and the screw may even cut its own internal thread into them. Many threaded fasteners can be described as either screws or bolts, depending on how they are used.
Bolts are often used to make a bolted joint. This is a combination of the nut applying an axial clamping force and also the shank of the bolt acting as a dowel, pinning the joint against sideways shear forces. For this reason, many bolts have a plain unthreaded shank (called the grip length) as this makes for a better, stronger dowel. The presence of the unthreaded shank has often been given as characteristic of bolts vs. screws, but this is incidental to its use, rather than defining. The grip length should be chosen carefully, to be around the same length as the thickness of the materials, and any washers, bolted together. Too short places the dowel shear load onto the threads, which may cause fretting wear on the hole. Too long prevents the nut from being tightened down correctly. No more than two turns of the thread should be within the hole.
Where a fastener forms its own thread in the component being fastened, it is called a screw. This is most obviously so when the thread is tapered (i.e. traditional wood screws), precluding the use of a nut, or when a sheet metal screw or other thread-forming screw is used.
A screw must always be turned to assemble the joint. Many bolts are held fixed in place during assembly, either by a tool or by a design of non-rotating bolt, such as a carriage bolt, and only the corresponding nut is turned.
MS Hex Nut Bolt
Minimum Order Quantity: 100 Piece
Usage/Application | Industrial |
Size | 100 mm |
Thread Type | BSPT |
Grade | A105 |
Material | Mild Steel |
Standard | ASTM |
Country of Origin | Made in India |
Mild steel fasteners are widely used for all general purposes where high strength and corrosion resistance is not required. Their low cost makes them ideal for everyday use. Mild steel Bolts and Screws conform to grades 4.6 and 4.8 and Nuts to grade 4. Higher grades of 5.6 and 5 are also arranged against order.
Finishes:
- Self colour, Zinc plated (with White/Blue/Yellow passivation), Hot Dip galvanised, Cadmium Plated, Blackened, Nickle plated and Chromium Plated.
Hexagonal Head Bolts and Screws:
- M3 X 6MM to M48 X 300 generally conforming to IS 1363(Part 1 & 2) 2002
- 3/16” X 1/2” to 2” X 12” in BSW threads generally conforming to BS 916
Hexagonal Full and Lock (Thin) Nuts:
- M2 to M60 generally conforming to IS 1363(Part 3)2002 (Hex Nut) and to IS 1364(Part 4)2003 (Lock (Thin) Nut)
- 1/8” to 2” in BSW threadsgenerally conforming to BS 916
- 1/2” to 3” in BSP threadsgenerally conforming to IS 3468-1991
Left hand thread nuts:
- 1/4" to 1" in BSW threads
- M6 to M24 in MM threads
Square Head Bolts & Nuts:
- M5 to M12generally conforming to IS 2585-2006
- 1/8” to 1/2” in BSW threads
Dom Nuts:
- M6 to M24
Flange (Collar) Bolts and nuts:
- M6 x 12 to M10 x 25mm
Eye Bolts and Eye nuts:
- Lifting Hooks M8 to M48
- Eye Bolt (Small Eye) M8 x 40 to M24 x 200
- Eye Nuts M12 to M 20
Slotted and Castle Nuts:
- M10 to M48 generally conforming to IS 2232-1967
- 3/8" to 2" in BSW threads
Nyloc Nuts:
- M3 to M48 generally conforming to IS7002-2005
- 1/4" to 1" in BSW, UNC, UNF and BSF threads.
Wing Nuts (Cast Iron):
- M6 to M16
- 1/4" to 5/8" in BSW threads
Studs:
- M6 x 25mm to M20 x 100mm
- 1/4" x 1" to 3/4" x 4"
Snap Head Rivets:
- 6 x 12mm to 24 x 100mm generally conforming to IS 1929/1982 and IS 2155/1982
- 1/4" x 1/2" to 1" x 4"
Carriage Bolts:
- 1/4" x 1 1/2" to 1/2" to 12"
- Special C.P. Carriage bolts with Nut and Washers 1/4" x 1 1/2" to 3" (for C.P.Aldrops)
Plain Washers:
- 3mm to 64mm generally conforming to IS 2016/67
- 1/8" to 2"
Taper Washers:
- 12mm to 24mm
U Bolts:
- Suitable for pipe sizes of 3/4" to 12" with bolt dia of 8mm to 12mm
Pipe Bolts:
- 5/16" x 3" to 7" suitable for pipes of 1" to 2"
J & L Bolts:
- 5/16" x 3" to 7"
GI Threaded Rods:
- M6 to M20 in 1Mtr & 2Mtr length
Connecter (Long) Nut:
- M6 to M16